I can think of few things worse than being halfway through shampooing my hair when I notice a spider on the shower wall. As an arachnophobic, it’s the type of situation that would bring me to tears. I’m also not a fan of any other creepy-crawlies, so you know that I’m going to be all over those potential entry points.
Unfortunately, bugs can possibly enter the bathroom through the fan’s vent. However, I would never leave a fellow bug-fearer without the comforting knowledge that, while possible, it’s not probable. This is thanks to a little device that is installed in the ductwork of a bathroom fan as a matter of routine.
Bugs can enter the bathroom through the vents. However, most bathroom ventilation systems are equipped with backdraft dampers. These control the direction of airflow but also stop bugs from entering the ductwork.
Bugs Can Enter Through the Fan Vent
In regards to bathroom exhaust fans, there are three main types: ceiling-mounted, inline, and wall-mounted. No matter which type is in your bathroom, they all function similarly and have to be connected to an exhaust duct leading to the exterior of the house.
This ductwork that connects the interior of your bathroom to the exterior of the house is more than wide enough for bugs to enter. Even the smallest ducts, which have a diameter of 3”, leave sufficient space for these tiny intruders.
So, without additional protection, bugs can easily pass through the ducts and access your bathroom.
While a wide array of bugs could use your bathroom ventilation system as a highway into the house, many will also make a safe haven out of your ducts and fan vent.
Roaches are a notorious culprit of hiding in vents.
Vents provide attractive conditions for these nasty critters because of the warm airflow and darkness within the duct.
Skin shedding, saliva, and feces produced by roaches can easily contaminate the air quality of your bathroom, as well as the rest of your house.
Obviously, the vent can’t be completely sealed off as it would defeat its purpose. Grids and meshes are a potential solution, but they often interfere with the function of the fan, especially those with openings small enough to stop all bugs.
Backdraft Dampers are an Effective Solution
Bugs coming through vents would be a much more common problem if it weren’t for backdraft dampers, which are installed in most bathroom exhaust fan systems (and if you don’t have one, you should definitely get one).
A damper, simply put, is a device that regulates the airflow inside air-handling equipment.
A backdraft damper is a specific type of damper. Typically, they are installed directly into the duct itself to ensure that air flows in one direction while simultaneously preventing the air from reversing directions.
Backdraft dampers typically come with spring-loaded flaps that close when there is no airflow. The flaps are triggered to open again when there is a change in air pressure, like when an exhaust fan turns on.
You may have more than one of these in your house as they are commonly used for bathroom fans as well as range hoods in the kitchen.
In addition to regulating the airflow in your home, a backdraft damper can also be a practical way to keep bugs out.
When deciding on the best backdraft damper to prevent bugs from getting through, consider an option that is spring-loaded with rubber seals, like the AC Infinity. Upon installation, the best place is directly into the duct or at the termination point.
- An antidraft duct insert designed for use with range hoods, bathroom fans and other home HVAC applications.
- Features outer rubber gaskets that create an airtight seal and grip between the damper and ducts.
- Mounts horizontally or vertically to prevent backflow and debris from entering ducting.
- Galvanized steel body with spring-loaded aluminum damper blades that open with minimal airflow.
Last update on 2024-11-18 / Affiliate links / Images from Amazon Product Advertising API
If your current backdraft damper is not doing the trick, then it might not be working properly. Sometimes, then seal is incomplete of the blades get stuck open.
Although the flaps would be open while the fan is on because of the air moving through, that airflow will make it more difficult for bugs and other pests, especially ones that fly, to get in.
Primary Purpose of Backdraft Dampers
The bug prevention aspect of a backdraft damper is only an added benefit. The primary purpose of a backdraft damper is centered around the airflow of a home.
There are many different areas of a house where a backdraft damper can be of use. These uses include bathroom exhaust systems, clothes dryer vents (backdraft dampers are mandatory for dryer vents), kitchen range hoods, and microwaves; the list could go on.
Essentially, while working with appliances such as the ones listed above, the backdraft damper allows air to flow through exhaust ducts to the exterior of your home. This is how humid, hot, or other unconditioned air is filtered out of houses.
When the exhaust systems are not in use, backdraft dampers also keep dusty, smoky, and exhausted air outside.
Furthermore, dampers can alleviate issues involving cold air leaks, water dripping from exhaust fans, as well as heat loss through bathroom fans.
As with any product, the quality determines its effectiveness. A higher-quality backdraft damper will provide all of the benefits discussed above at a level closer to satisfactory than a lower-quality one.
There are a few different types of backdraft dampers that you as a consumer can choose from; spring dampers, electric dampers, and caped dampers.
I would recommend further inquiry on the topic of backdraft dampers to make a decision on which damper works best for you.
However, spring-loaded backdraft dampers, installed directly into the ducts, are a common and reliable option.
At the end of the day, as a consumer, you want to make sure that you have a quality appliance so that you can reap the benefits of better airflow control and energy-saving.
How to Check if Your Backdraft Damper Is Working
Most houses and exhaust fan systems should come with a backdraft damper installed. Regarding the exhaust fan systems, the damper could be a factory-installed piece or a separate part chosen by the installer.
It’s important to check the status of your dampers and replace them if necessary. Dampers can become rusty and worn or even broken by outside elements as they open to the exterior of houses in most cases.
If you notice cold air blowing through your bathroom fan, you may want to consider backdraft damper replacement. If your fan is making noise while off, it can be another sign the damper has failed.
Installing or Replacing Backdraft Damper
When it comes to DIY projects, of course, experience with that sort of handy work will definitely give you an advantage. But, if you’re not so confident tackling home-improvement projects, you’ll be glad to know that installing a backdraft damper isn’t as difficult as it sounds and can be done without professional aid.
You’ll need at the very least these tools (although, naturally, the tools required will vary depending on the location of the installment and the make of your backdraft damper.):
- tape measure (amazon link).
- permanent marker.
- drill with 5/16-inch hex head adapter (amazon link).
- caulk (amazon link).
- drop-in caulk gun (amazon link).
As with any DIY endeavor, you’ll need a YouTube tutorial video, like the ones below, to get you through the journey.
Getting Bugs out of Vents
Now that you know how to stop the bugs from getting in through the vents, you need to make sure that there are none left in the vent. It’s not a simple task, but there are a few options if you do run into this problem.
Although it would be the quickest and easiest way to rid your vents of bugs if it worked, do NOT spray insect or bug repellent of any kind into your ductwork. Not only is this ineffective and smelly, but it is also a risk to your health.
Traps are a possible solution to catch bugs running wild through your ventilation. Glue traps are commonly used with some sort of lure to attract the bugs.
Vertically aligned vents make it difficult to use traditional traps, as just suggested. In this case, clear packing tape has been used to place across the front of vents. Simply cut slits in the tape so that air can still pass through, and when the bug tries to escape, it will get caught in the adhesive.
Sources
https://www.homeclick.com/how-bathroom-exhaust-fans-work.htm?bid=dept
https://www.vulcantermite.com/home-pest-control/can-roaches-come-air-vents/
https://en.wikipedia.org/wiki/Damper_(flow)
https://homesteady.com/12358070/how-to-make-a-duct-board-plenum